Total
12147 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2022-49654 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: dsa: qca8k: reset cpu port on MTU change It was discovered that the Documentation lacks of a fundamental detail on how to correctly change the MAX_FRAME_SIZE of the switch. In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the switch panics and cease to send any packet. This cause the mgmt ethernet system to not receive any packet (the slow fallback still works) and makes the device not reachable. To recover from this a switch reset is required. To correctly handle this, turn off the cpu ports before changing the MAX_FRAME_SIZE and turn on again after the value is applied. | |||||
| CVE-2022-49650 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: dmaengine: qcom: bam_dma: fix runtime PM underflow Commit dbad41e7bb5f ("dmaengine: qcom: bam_dma: check if the runtime pm enabled") caused unbalanced pm_runtime_get/put() calls when the bam is controlled remotely. This commit reverts it and just enables pm_runtime in all cases, the clk_* functions already just nop when the clock is NULL. Also clean up a bit by removing unnecessary bamclk null checks. | |||||
| CVE-2022-49646 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix queue selection for mesh/OCB interfaces When using iTXQ, the code assumes that there is only one vif queue for broadcast packets, using the BE queue. Allowing non-BE queue marking violates that assumption and txq->ac == skb_queue_mapping is no longer guaranteed. This can cause issues with queue handling in the driver and also causes issues with the recent ATF change, resulting in an AQL underflow warning. | |||||
| CVE-2022-49645 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: drm/panfrost: Fix shrinker list corruption by madvise IOCTL Calling madvise IOCTL twice on BO causes memory shrinker list corruption and crashes kernel because BO is already on the list and it's added to the list again, while BO should be removed from the list before it's re-added. Fix it. | |||||
| CVE-2022-49642 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: stmmac: dwc-qos: Disable split header for Tegra194 There is a long-standing issue with the Synopsys DWC Ethernet driver for Tegra194 where random system crashes have been observed [0]. The problem occurs when the split header feature is enabled in the stmmac driver. In the bad case, a larger than expected buffer length is received and causes the calculation of the total buffer length to overflow. This results in a very large buffer length that causes the kernel to crash. Why this larger buffer length is received is not clear, however, the feedback from the NVIDIA design team is that the split header feature is not supported for Tegra194. Therefore, disable split header support for Tegra194 to prevent these random crashes from occurring. [0] https://lore.kernel.org/linux-tegra/b0b17697-f23e-8fa5-3757-604a86f3a095@nvidia.com/ | |||||
| CVE-2022-49635 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: drm/i915/selftests: fix subtraction overflow bug On some machines hole_end can be small enough to cause subtraction overflow. On the other side (addr + 2 * min_alignment) can overflow in case of mock tests. This patch should handle both cases. (cherry picked from commit ab3edc679c552a466e4bf0b11af3666008bd65a2) | |||||
| CVE-2022-49628 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: stmmac: fix leaks in probe These two error paths should clean up before returning. | |||||
| CVE-2022-49625 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: sfc: fix kernel panic when creating VF When creating VFs a kernel panic can happen when calling to efx_ef10_try_update_nic_stats_vf. When releasing a DMA coherent buffer, sometimes, I don't know in what specific circumstances, it has to unmap memory with vunmap. It is disallowed to do that in IRQ context or with BH disabled. Otherwise, we hit this line in vunmap, causing the crash: BUG_ON(in_interrupt()); This patch reenables BH to release the buffer. Log messages when the bug is hit: kernel BUG at mm/vmalloc.c:2727! invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 6 PID: 1462 Comm: NetworkManager Kdump: loaded Tainted: G I --------- --- 5.14.0-119.el9.x86_64 #1 Hardware name: Dell Inc. PowerEdge R740/06WXJT, BIOS 2.8.2 08/27/2020 RIP: 0010:vunmap+0x2e/0x30 ...skip... Call Trace: __iommu_dma_free+0x96/0x100 efx_nic_free_buffer+0x2b/0x40 [sfc] efx_ef10_try_update_nic_stats_vf+0x14a/0x1c0 [sfc] efx_ef10_update_stats_vf+0x18/0x40 [sfc] efx_start_all+0x15e/0x1d0 [sfc] efx_net_open+0x5a/0xe0 [sfc] __dev_open+0xe7/0x1a0 __dev_change_flags+0x1d7/0x240 dev_change_flags+0x21/0x60 ...skip... | |||||
| CVE-2022-49624 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: net: atlantic: remove aq_nic_deinit() when resume aq_nic_deinit() has been called while suspending, so we don't have to call it again on resume. Actually, call it again leads to another hang issue when resuming from S3. Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992345] Call Trace: Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992346] <TASK> Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992348] aq_nic_deinit+0xb4/0xd0 [atlantic] Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992356] aq_pm_thaw+0x7f/0x100 [atlantic] Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992362] pci_pm_resume+0x5c/0x90 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992366] ? pci_pm_thaw+0x80/0x80 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992368] dpm_run_callback+0x4e/0x120 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992371] device_resume+0xad/0x200 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992373] async_resume+0x1e/0x40 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992374] async_run_entry_fn+0x33/0x120 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992377] process_one_work+0x220/0x3c0 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992380] worker_thread+0x4d/0x3f0 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992382] ? process_one_work+0x3c0/0x3c0 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992384] kthread+0x12a/0x150 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992386] ? set_kthread_struct+0x40/0x40 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992387] ret_from_fork+0x22/0x30 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992391] </TASK> Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992392] ---[ end trace 1ec8c79604ed5e0d ]--- Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992394] PM: dpm_run_callback(): pci_pm_resume+0x0/0x90 returns -110 Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992397] atlantic 0000:02:00.0: PM: failed to resume async: error -110 | |||||
| CVE-2022-49617 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: ASoC: Intel: sof_sdw: handle errors on card registration If the card registration fails, typically because of deferred probes, the device properties added for headset codecs are not removed, which leads to kernel oopses in driver bind/unbind tests. We already clean-up the device properties when the card is removed, this code can be moved as a helper and called upon card registration errors. | |||||
| CVE-2022-49616 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: ASoC: rt7*-sdw: harden jack_detect_handler Realtek headset codec drivers typically check if the card is instantiated before proceeding with the jack detection. The rt700, rt711 and rt711-sdca are however missing a check on the card pointer, which can lead to NULL dereferences encountered in driver bind/unbind tests. | |||||
| CVE-2022-49613 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: serial: 8250: Fix PM usage_count for console handover When console is enabled, univ8250_console_setup() calls serial8250_console_setup() before .dev is set to uart_port. Therefore, it will not call pm_runtime_get_sync(). Later, when the actual driver is going to take over univ8250_console_exit() is called. As .dev is already set, serial8250_console_exit() makes pm_runtime_put_sync() call with usage count being zero triggering PM usage count warning (extra debug for univ8250_console_setup(), univ8250_console_exit(), and serial8250_register_ports()): [ 0.068987] univ8250_console_setup ttyS0 nodev [ 0.499670] printk: console [ttyS0] enabled [ 0.717955] printk: console [ttyS0] printing thread started [ 1.960163] serial8250_register_ports assigned dev for ttyS0 [ 1.976830] printk: console [ttyS0] disabled [ 1.976888] printk: console [ttyS0] printing thread stopped [ 1.977073] univ8250_console_exit ttyS0 usage:0 [ 1.977075] serial8250 serial8250: Runtime PM usage count underflow! [ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A [ 1.977812] univ8250_console_setup ttyS0 usage:2 [ 1.978167] printk: console [ttyS0] printing thread started [ 1.978203] printk: console [ttyS0] enabled To fix the issue, call pm_runtime_get_sync() in serial8250_register_ports() as soon as .dev is set for an uart_port if it has console enabled. This problem became apparent only recently because 82586a721595 ("PM: runtime: Avoid device usage count underflows") added the warning printout. I confirmed this problem also occurs with v5.18 (w/o the warning printout, obviously). | |||||
| CVE-2022-49612 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: power: supply: core: Fix boundary conditions in interpolation The functions power_supply_temp2resist_simple and power_supply_ocv2cap_simple handle boundary conditions incorrectly. The change was introduced in a4585ba2050f460f749bbaf2b67bd56c41e30283 ("power: supply: core: Use library interpolation"). There are two issues: First, the lines "high = i - 1" and "high = i" in ocv2cap have the wrong order compared to temp2resist. As a consequence, ocv2cap sets high=-1 if ocv>table[0].ocv, which causes an out-of-bounds read. Second, the logic of temp2resist is also not correct. Consider the case table[] = {{20, 100}, {10, 80}, {0, 60}}. For temp=5, we expect a resistance of 70% by interpolation. However, temp2resist sets high=low=2 and returns 60. | |||||
| CVE-2022-49611 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: x86/speculation: Fill RSB on vmexit for IBRS Prevent RSB underflow/poisoning attacks with RSB. While at it, add a bunch of comments to attempt to document the current state of tribal knowledge about RSB attacks and what exactly is being mitigated. | |||||
| CVE-2022-49610 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: KVM: VMX: Prevent RSB underflow before vmenter On VMX, there are some balanced returns between the time the guest's SPEC_CTRL value is written, and the vmenter. Balanced returns (matched by a preceding call) are usually ok, but it's at least theoretically possible an NMI with a deep call stack could empty the RSB before one of the returns. For maximum paranoia, don't allow *any* returns (balanced or otherwise) between the SPEC_CTRL write and the vmenter. [ bp: Fix 32-bit build. ] | |||||
| CVE-2022-49606 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Fix sleep from invalid context BUG Taking the qos_mutex to process RoCEv2 QP's on netdev events causes a kernel splat. Fix this by removing the handling for RoCEv2 in irdma_cm_teardown_connections that uses the mutex. This handling is only needed for iWARP to avoid having connections established while the link is down or having connections remain functional after the IP address is removed. BUG: sleeping function called from invalid context at kernel/locking/mutex. Call Trace: kernel: dump_stack+0x66/0x90 kernel: ___might_sleep.cold.92+0x8d/0x9a kernel: mutex_lock+0x1c/0x40 kernel: irdma_cm_teardown_connections+0x28e/0x4d0 [irdma] kernel: ? check_preempt_curr+0x7a/0x90 kernel: ? select_idle_sibling+0x22/0x3c0 kernel: ? select_task_rq_fair+0x94c/0xc90 kernel: ? irdma_exec_cqp_cmd+0xc27/0x17c0 [irdma] kernel: ? __wake_up_common+0x7a/0x190 kernel: irdma_if_notify+0x3cc/0x450 [irdma] kernel: ? sched_clock_cpu+0xc/0xb0 kernel: irdma_inet6addr_event+0xc6/0x150 [irdma] | |||||
| CVE-2022-49605 | 1 Linux | 1 Linux Kernel | 2025-10-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: igc: Reinstate IGC_REMOVED logic and implement it properly The initially merged version of the igc driver code (via commit 146740f9abc4, "igc: Add support for PF") contained the following IGC_REMOVED checks in the igc_rd32/wr32() MMIO accessors: u32 igc_rd32(struct igc_hw *hw, u32 reg) { u8 __iomem *hw_addr = READ_ONCE(hw->hw_addr); u32 value = 0; if (IGC_REMOVED(hw_addr)) return ~value; value = readl(&hw_addr[reg]); /* reads should not return all F's */ if (!(~value) && (!reg || !(~readl(hw_addr)))) hw->hw_addr = NULL; return value; } And: #define wr32(reg, val) \ do { \ u8 __iomem *hw_addr = READ_ONCE((hw)->hw_addr); \ if (!IGC_REMOVED(hw_addr)) \ writel((val), &hw_addr[(reg)]); \ } while (0) E.g. igb has similar checks in its MMIO accessors, and has a similar macro E1000_REMOVED, which is implemented as follows: #define E1000_REMOVED(h) unlikely(!(h)) These checks serve to detect and take note of an 0xffffffff MMIO read return from the device, which can be caused by a PCIe link flap or some other kind of PCI bus error, and to avoid performing MMIO reads and writes from that point onwards. However, the IGC_REMOVED macro was not originally implemented: #ifndef IGC_REMOVED #define IGC_REMOVED(a) (0) #endif /* IGC_REMOVED */ This led to the IGC_REMOVED logic to be removed entirely in a subsequent commit (commit 3c215fb18e70, "igc: remove IGC_REMOVED function"), with the rationale that such checks matter only for virtualization and that igc does not support virtualization -- but a PCIe device can become detached even without virtualization being in use, and without proper checks, a PCIe bus error affecting an igc adapter will lead to various NULL pointer dereferences, as the first access after the error will set hw->hw_addr to NULL, and subsequent accesses will blindly dereference this now-NULL pointer. This patch reinstates the IGC_REMOVED checks in igc_rd32/wr32(), and implements IGC_REMOVED the way it is done for igb, by checking for the unlikely() case of hw_addr being NULL. This change prevents the oopses seen when a PCIe link flap occurs on an igc adapter. | |||||
| CVE-2024-58009 | 1 Linux | 1 Linux Kernel | 2025-10-22 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: handle NULL sock pointer in l2cap_sock_alloc A NULL sock pointer is passed into l2cap_sock_alloc() when it is called from l2cap_sock_new_connection_cb() and the error handling paths should also be aware of it. Seemingly a more elegant solution would be to swap bt_sock_alloc() and l2cap_chan_create() calls since they are not interdependent to that moment but then l2cap_chan_create() adds the soon to be deallocated and still dummy-initialized channel to the global list accessible by many L2CAP paths. The channel would be removed from the list in short period of time but be a bit more straight-forward here and just check for NULL instead of changing the order of function calls. Found by Linux Verification Center (linuxtesting.org) with SVACE static analysis tool. | |||||
| CVE-2024-58014 | 1 Linux | 1 Linux Kernel | 2025-10-22 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy() In 'wlc_phy_iqcal_gainparams_nphy()', add gain range check to WARN() instead of possible out-of-bounds 'tbl_iqcal_gainparams_nphy' access. Compile tested only. Found by Linux Verification Center (linuxtesting.org) with SVACE. | |||||
| CVE-2024-58015 | 1 Linux | 1 Linux Kernel | 2025-10-22 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Fix for out-of bound access error Selfgen stats are placed in a buffer using print_array_to_buf_index() function. Array length parameter passed to the function is too big, resulting in possible out-of bound memory error. Decreasing buffer size by one fixes faulty upper bound of passed array. Discovered in coverity scan, CID 1600742 and CID 1600758 | |||||