Filtered by vendor Linux
Subscribe
Total
12249 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2023-52843 | 1 Linux | 1 Linux Kernel | 2025-09-24 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: llc: verify mac len before reading mac header LLC reads the mac header with eth_hdr without verifying that the skb has an Ethernet header. Syzbot was able to enter llc_rcv on a tun device. Tun can insert packets without mac len and with user configurable skb->protocol (passing a tun_pi header when not configuring IFF_NO_PI). BUG: KMSAN: uninit-value in llc_station_ac_send_test_r net/llc/llc_station.c:81 [inline] BUG: KMSAN: uninit-value in llc_station_rcv+0x6fb/0x1290 net/llc/llc_station.c:111 llc_station_ac_send_test_r net/llc/llc_station.c:81 [inline] llc_station_rcv+0x6fb/0x1290 net/llc/llc_station.c:111 llc_rcv+0xc5d/0x14a0 net/llc/llc_input.c:218 __netif_receive_skb_one_core net/core/dev.c:5523 [inline] __netif_receive_skb+0x1a6/0x5a0 net/core/dev.c:5637 netif_receive_skb_internal net/core/dev.c:5723 [inline] netif_receive_skb+0x58/0x660 net/core/dev.c:5782 tun_rx_batched+0x3ee/0x980 drivers/net/tun.c:1555 tun_get_user+0x54c5/0x69c0 drivers/net/tun.c:2002 Add a mac_len test before all three eth_hdr(skb) calls under net/llc. There are further uses in include/net/llc_pdu.h. All these are protected by a test skb->protocol == ETH_P_802_2. Which does not protect against this tun scenario. But the mac_len test added in this patch in llc_fixup_skb will indirectly protect those too. That is called from llc_rcv before any other LLC code. It is tempting to just add a blanket mac_len check in llc_rcv, but not sure whether that could break valid LLC paths that do not assume an Ethernet header. 802.2 LLC may be used on top of non-802.3 protocols in principle. The below referenced commit shows that used to, on top of Token Ring. At least one of the three eth_hdr uses goes back to before the start of git history. But the one that syzbot exercises is introduced in this commit. That commit is old enough (2008), that effectively all stable kernels should receive this. | |||||
| CVE-2025-23303 | 4 Apple, Linux, Microsoft and 1 more | 4 Macos, Linux Kernel, Windows and 1 more | 2025-09-23 | N/A | 7.8 HIGH |
| NVIDIA NeMo Framework for all platforms contains a vulnerability where a user could cause a deserialization of untrusted data by remote code execution. A successful exploit of this vulnerability might lead to code execution and data tampering. | |||||
| CVE-2023-52836 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: locking/ww_mutex/test: Fix potential workqueue corruption In some cases running with the test-ww_mutex code, I was seeing odd behavior where sometimes it seemed flush_workqueue was returning before all the work threads were finished. Often this would cause strange crashes as the mutexes would be freed while they were being used. Looking at the code, there is a lifetime problem as the controlling thread that spawns the work allocates the "struct stress" structures that are passed to the workqueue threads. Then when the workqueue threads are finished, they free the stress struct that was passed to them. Unfortunately the workqueue work_struct node is in the stress struct. Which means the work_struct is freed before the work thread returns and while flush_workqueue is waiting. It seems like a better idea to have the controlling thread both allocate and free the stress structures, so that we can be sure we don't corrupt the workqueue by freeing the structure prematurely. So this patch reworks the test to do so, and with this change I no longer see the early flush_workqueue returns. | |||||
| CVE-2023-52835 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: perf/core: Bail out early if the request AUX area is out of bound When perf-record with a large AUX area, e.g 4GB, it fails with: #perf record -C 0 -m ,4G -e arm_spe_0// -- sleep 1 failed to mmap with 12 (Cannot allocate memory) and it reveals a WARNING with __alloc_pages(): ------------[ cut here ]------------ WARNING: CPU: 44 PID: 17573 at mm/page_alloc.c:5568 __alloc_pages+0x1ec/0x248 Call trace: __alloc_pages+0x1ec/0x248 __kmalloc_large_node+0xc0/0x1f8 __kmalloc_node+0x134/0x1e8 rb_alloc_aux+0xe0/0x298 perf_mmap+0x440/0x660 mmap_region+0x308/0x8a8 do_mmap+0x3c0/0x528 vm_mmap_pgoff+0xf4/0x1b8 ksys_mmap_pgoff+0x18c/0x218 __arm64_sys_mmap+0x38/0x58 invoke_syscall+0x50/0x128 el0_svc_common.constprop.0+0x58/0x188 do_el0_svc+0x34/0x50 el0_svc+0x34/0x108 el0t_64_sync_handler+0xb8/0xc0 el0t_64_sync+0x1a4/0x1a8 'rb->aux_pages' allocated by kcalloc() is a pointer array which is used to maintains AUX trace pages. The allocated page for this array is physically contiguous (and virtually contiguous) with an order of 0..MAX_ORDER. If the size of pointer array crosses the limitation set by MAX_ORDER, it reveals a WARNING. So bail out early with -ENOMEM if the request AUX area is out of bound, e.g.: #perf record -C 0 -m ,4G -e arm_spe_0// -- sleep 1 failed to mmap with 12 (Cannot allocate memory) | |||||
| CVE-2023-52831 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: cpu/hotplug: Don't offline the last non-isolated CPU If a system has isolated CPUs via the "isolcpus=" command line parameter, then an attempt to offline the last housekeeping CPU will result in a WARN_ON() when rebuilding the scheduler domains and a subsequent panic due to and unhandled empty CPU mas in partition_sched_domains_locked(). cpuset_hotplug_workfn() rebuild_sched_domains_locked() ndoms = generate_sched_domains(&doms, &attr); cpumask_and(doms[0], top_cpuset.effective_cpus, housekeeping_cpumask(HK_FLAG_DOMAIN)); Thus results in an empty CPU mask which triggers the warning and then the subsequent crash: WARNING: CPU: 4 PID: 80 at kernel/sched/topology.c:2366 build_sched_domains+0x120c/0x1408 Call trace: build_sched_domains+0x120c/0x1408 partition_sched_domains_locked+0x234/0x880 rebuild_sched_domains_locked+0x37c/0x798 rebuild_sched_domains+0x30/0x58 cpuset_hotplug_workfn+0x2a8/0x930 Unable to handle kernel paging request at virtual address fffe80027ab37080 partition_sched_domains_locked+0x318/0x880 rebuild_sched_domains_locked+0x37c/0x798 Aside of the resulting crash, it does not make any sense to offline the last last housekeeping CPU. Prevent this by masking out the non-housekeeping CPUs when selecting a target CPU for initiating the CPU unplug operation via the work queue. | |||||
| CVE-2023-52816 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Fix shift out-of-bounds issue [ 567.613292] shift exponent 255 is too large for 64-bit type 'long unsigned int' [ 567.614498] CPU: 5 PID: 238 Comm: kworker/5:1 Tainted: G OE 6.2.0-34-generic #34~22.04.1-Ubuntu [ 567.614502] Hardware name: AMD Splinter/Splinter-RPL, BIOS WS43927N_871 09/25/2023 [ 567.614504] Workqueue: events send_exception_work_handler [amdgpu] [ 567.614748] Call Trace: [ 567.614750] <TASK> [ 567.614753] dump_stack_lvl+0x48/0x70 [ 567.614761] dump_stack+0x10/0x20 [ 567.614763] __ubsan_handle_shift_out_of_bounds+0x156/0x310 [ 567.614769] ? srso_alias_return_thunk+0x5/0x7f [ 567.614773] ? update_sd_lb_stats.constprop.0+0xf2/0x3c0 [ 567.614780] svm_range_split_by_granularity.cold+0x2b/0x34 [amdgpu] [ 567.615047] ? srso_alias_return_thunk+0x5/0x7f [ 567.615052] svm_migrate_to_ram+0x185/0x4d0 [amdgpu] [ 567.615286] do_swap_page+0x7b6/0xa30 [ 567.615291] ? srso_alias_return_thunk+0x5/0x7f [ 567.615294] ? __free_pages+0x119/0x130 [ 567.615299] handle_pte_fault+0x227/0x280 [ 567.615303] __handle_mm_fault+0x3c0/0x720 [ 567.615311] handle_mm_fault+0x119/0x330 [ 567.615314] ? lock_mm_and_find_vma+0x44/0x250 [ 567.615318] do_user_addr_fault+0x1a9/0x640 [ 567.615323] exc_page_fault+0x81/0x1b0 [ 567.615328] asm_exc_page_fault+0x27/0x30 [ 567.615332] RIP: 0010:__get_user_8+0x1c/0x30 | |||||
| CVE-2023-52804 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: fs/jfs: Add validity check for db_maxag and db_agpref Both db_maxag and db_agpref are used as the index of the db_agfree array, but there is currently no validity check for db_maxag and db_agpref, which can lead to errors. The following is related bug reported by Syzbot: UBSAN: array-index-out-of-bounds in fs/jfs/jfs_dmap.c:639:20 index 7936 is out of range for type 'atomic_t[128]' Add checking that the values of db_maxag and db_agpref are valid indexes for the db_agfree array. | |||||
| CVE-2024-56552 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 4.7 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drm/xe/guc_submit: fix race around suspend_pending Currently in some testcases we can trigger: xe 0000:03:00.0: [drm] Assertion `exec_queue_destroyed(q)` failed! .... WARNING: CPU: 18 PID: 2640 at drivers/gpu/drm/xe/xe_guc_submit.c:1826 xe_guc_sched_done_handler+0xa54/0xef0 [xe] xe 0000:03:00.0: [drm] *ERROR* GT1: DEREGISTER_DONE: Unexpected engine state 0x00a1, guc_id=57 Looking at a snippet of corresponding ftrace for this GuC id we can see: 162.673311: xe_sched_msg_add: dev=0000:03:00.0, gt=1 guc_id=57, opcode=3 162.673317: xe_sched_msg_recv: dev=0000:03:00.0, gt=1 guc_id=57, opcode=3 162.673319: xe_exec_queue_scheduling_disable: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0x29, flags=0x0 162.674089: xe_exec_queue_kill: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0x29, flags=0x0 162.674108: xe_exec_queue_close: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0xa9, flags=0x0 162.674488: xe_exec_queue_scheduling_done: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0xa9, flags=0x0 162.678452: xe_exec_queue_deregister: dev=0000:03:00.0, 1:0x2, gt=1, width=1, guc_id=57, guc_state=0xa1, flags=0x0 It looks like we try to suspend the queue (opcode=3), setting suspend_pending and triggering a disable_scheduling. The user then closes the queue. However the close will also forcefully signal the suspend fence after killing the queue, later when the G2H response for disable_scheduling comes back we have now cleared suspend_pending when signalling the suspend fence, so the disable_scheduling now incorrectly tries to also deregister the queue. This leads to warnings since the queue has yet to even be marked for destruction. We also seem to trigger errors later with trying to double unregister the same queue. To fix this tweak the ordering when handling the response to ensure we don't race with a disable_scheduling that didn't actually intend to perform an unregister. The destruction path should now also correctly wait for any pending_disable before marking as destroyed. (cherry picked from commit f161809b362f027b6d72bd998e47f8f0bad60a2e) | |||||
| CVE-2024-56563 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: ceph: fix cred leak in ceph_mds_check_access() get_current_cred() increments the reference counter, but the put_cred() call was missing. | |||||
| CVE-2021-47458 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: ocfs2: mount fails with buffer overflow in strlen Starting with kernel 5.11 built with CONFIG_FORTIFY_SOURCE mouting an ocfs2 filesystem with either o2cb or pcmk cluster stack fails with the trace below. Problem seems to be that strings for cluster stack and cluster name are not guaranteed to be null terminated in the disk representation, while strlcpy assumes that the source string is always null terminated. This causes a read outside of the source string triggering the buffer overflow detection. detected buffer overflow in strlen ------------[ cut here ]------------ kernel BUG at lib/string.c:1149! invalid opcode: 0000 [#1] SMP PTI CPU: 1 PID: 910 Comm: mount.ocfs2 Not tainted 5.14.0-1-amd64 #1 Debian 5.14.6-2 RIP: 0010:fortify_panic+0xf/0x11 ... Call Trace: ocfs2_initialize_super.isra.0.cold+0xc/0x18 [ocfs2] ocfs2_fill_super+0x359/0x19b0 [ocfs2] mount_bdev+0x185/0x1b0 legacy_get_tree+0x27/0x40 vfs_get_tree+0x25/0xb0 path_mount+0x454/0xa20 __x64_sys_mount+0x103/0x140 do_syscall_64+0x3b/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae | |||||
| CVE-2021-47431 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix gart.bo pin_count leak gmc_v{9,10}_0_gart_disable() isn't called matched with correspoding gart_enbale function in SRIOV case. This will lead to gart.bo pin_count leak on driver unload. | |||||
| CVE-2021-47425 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: i2c: acpi: fix resource leak in reconfiguration device addition acpi_i2c_find_adapter_by_handle() calls bus_find_device() which takes a reference on the adapter which is never released which will result in a reference count leak and render the adapter unremovable. Make sure to put the adapter after creating the client in the same manner that we do for OF. [wsa: fixed title] | |||||
| CVE-2021-47424 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: i40e: Fix freeing of uninitialized misc IRQ vector When VSI set up failed in i40e_probe() as part of PF switch set up driver was trying to free misc IRQ vectors in i40e_clear_interrupt_scheme and produced a kernel Oops: Trying to free already-free IRQ 266 WARNING: CPU: 0 PID: 5 at kernel/irq/manage.c:1731 __free_irq+0x9a/0x300 Workqueue: events work_for_cpu_fn RIP: 0010:__free_irq+0x9a/0x300 Call Trace: ? synchronize_irq+0x3a/0xa0 free_irq+0x2e/0x60 i40e_clear_interrupt_scheme+0x53/0x190 [i40e] i40e_probe.part.108+0x134b/0x1a40 [i40e] ? kmem_cache_alloc+0x158/0x1c0 ? acpi_ut_update_ref_count.part.1+0x8e/0x345 ? acpi_ut_update_object_reference+0x15e/0x1e2 ? strstr+0x21/0x70 ? irq_get_irq_data+0xa/0x20 ? mp_check_pin_attr+0x13/0xc0 ? irq_get_irq_data+0xa/0x20 ? mp_map_pin_to_irq+0xd3/0x2f0 ? acpi_register_gsi_ioapic+0x93/0x170 ? pci_conf1_read+0xa4/0x100 ? pci_bus_read_config_word+0x49/0x70 ? do_pci_enable_device+0xcc/0x100 local_pci_probe+0x41/0x90 work_for_cpu_fn+0x16/0x20 process_one_work+0x1a7/0x360 worker_thread+0x1cf/0x390 ? create_worker+0x1a0/0x1a0 kthread+0x112/0x130 ? kthread_flush_work_fn+0x10/0x10 ret_from_fork+0x1f/0x40 The problem is that at that point misc IRQ vectors were not allocated yet and we get a call trace that driver is trying to free already free IRQ vectors. Add a check in i40e_clear_interrupt_scheme for __I40E_MISC_IRQ_REQUESTED PF state before calling i40e_free_misc_vector. This state is set only if misc IRQ vectors were properly initialized. | |||||
| CVE-2021-47393 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: hwmon: (mlxreg-fan) Return non-zero value when fan current state is enforced from sysfs Fan speed minimum can be enforced from sysfs. For example, setting current fan speed to 20 is used to enforce fan speed to be at 100% speed, 19 - to be not below 90% speed, etcetera. This feature provides ability to limit fan speed according to some system wise considerations, like absence of some replaceable units or high system ambient temperature. Request for changing fan minimum speed is configuration request and can be set only through 'sysfs' write procedure. In this situation value of argument 'state' is above nominal fan speed maximum. Return non-zero code in this case to avoid thermal_cooling_device_stats_update() call, because in this case statistics update violates thermal statistics table range. The issues is observed in case kernel is configured with option CONFIG_THERMAL_STATISTICS. Here is the trace from KASAN: [ 159.506659] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x7d/0xb0 [ 159.516016] Read of size 4 at addr ffff888116163840 by task hw-management.s/7444 [ 159.545625] Call Trace: [ 159.548366] dump_stack+0x92/0xc1 [ 159.552084] ? thermal_cooling_device_stats_update+0x7d/0xb0 [ 159.635869] thermal_zone_device_update+0x345/0x780 [ 159.688711] thermal_zone_device_set_mode+0x7d/0xc0 [ 159.694174] mlxsw_thermal_modules_init+0x48f/0x590 [mlxsw_core] [ 159.700972] ? mlxsw_thermal_set_cur_state+0x5a0/0x5a0 [mlxsw_core] [ 159.731827] mlxsw_thermal_init+0x763/0x880 [mlxsw_core] [ 160.070233] RIP: 0033:0x7fd995909970 [ 160.074239] Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff .. [ 160.095242] RSP: 002b:00007fff54f5d938 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 160.103722] RAX: ffffffffffffffda RBX: 0000000000000013 RCX: 00007fd995909970 [ 160.111710] RDX: 0000000000000013 RSI: 0000000001906008 RDI: 0000000000000001 [ 160.119699] RBP: 0000000001906008 R08: 00007fd995bc9760 R09: 00007fd996210700 [ 160.127687] R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000013 [ 160.135673] R13: 0000000000000001 R14: 00007fd995bc8600 R15: 0000000000000013 [ 160.143671] [ 160.145338] Allocated by task 2924: [ 160.149242] kasan_save_stack+0x19/0x40 [ 160.153541] __kasan_kmalloc+0x7f/0xa0 [ 160.157743] __kmalloc+0x1a2/0x2b0 [ 160.161552] thermal_cooling_device_setup_sysfs+0xf9/0x1a0 [ 160.167687] __thermal_cooling_device_register+0x1b5/0x500 [ 160.173833] devm_thermal_of_cooling_device_register+0x60/0xa0 [ 160.180356] mlxreg_fan_probe+0x474/0x5e0 [mlxreg_fan] [ 160.248140] [ 160.249807] The buggy address belongs to the object at ffff888116163400 [ 160.249807] which belongs to the cache kmalloc-1k of size 1024 [ 160.263814] The buggy address is located 64 bytes to the right of [ 160.263814] 1024-byte region [ffff888116163400, ffff888116163800) [ 160.277536] The buggy address belongs to the page: [ 160.282898] page:0000000012275840 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888116167000 pfn:0x116160 [ 160.294872] head:0000000012275840 order:3 compound_mapcount:0 compound_pincount:0 [ 160.303251] flags: 0x200000000010200(slab|head|node=0|zone=2) [ 160.309694] raw: 0200000000010200 ffffea00046f7208 ffffea0004928208 ffff88810004dbc0 [ 160.318367] raw: ffff888116167000 00000000000a0006 00000001ffffffff 0000000000000000 [ 160.327033] page dumped because: kasan: bad access detected [ 160.333270] [ 160.334937] Memory state around the buggy address: [ 160.356469] >ffff888116163800: fc .. | |||||
| CVE-2021-47392 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/cma: Fix listener leak in rdma_cma_listen_on_all() failure If cma_listen_on_all() fails it leaves the per-device ID still on the listen_list but the state is not set to RDMA_CM_ADDR_BOUND. When the cmid is eventually destroyed cma_cancel_listens() is not called due to the wrong state, however the per-device IDs are still holding the refcount preventing the ID from being destroyed, thus deadlocking: task:rping state:D stack: 0 pid:19605 ppid: 47036 flags:0x00000084 Call Trace: __schedule+0x29a/0x780 ? free_unref_page_commit+0x9b/0x110 schedule+0x3c/0xa0 schedule_timeout+0x215/0x2b0 ? __flush_work+0x19e/0x1e0 wait_for_completion+0x8d/0xf0 _destroy_id+0x144/0x210 [rdma_cm] ucma_close_id+0x2b/0x40 [rdma_ucm] __destroy_id+0x93/0x2c0 [rdma_ucm] ? __xa_erase+0x4a/0xa0 ucma_destroy_id+0x9a/0x120 [rdma_ucm] ucma_write+0xb8/0x130 [rdma_ucm] vfs_write+0xb4/0x250 ksys_write+0xb5/0xd0 ? syscall_trace_enter.isra.19+0x123/0x190 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Ensure that cma_listen_on_all() atomically unwinds its action under the lock during error. | |||||
| CVE-2021-47391 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/cma: Ensure rdma_addr_cancel() happens before issuing more requests The FSM can run in a circle allowing rdma_resolve_ip() to be called twice on the same id_priv. While this cannot happen without going through the work, it violates the invariant that the same address resolution background request cannot be active twice. CPU 1 CPU 2 rdma_resolve_addr(): RDMA_CM_IDLE -> RDMA_CM_ADDR_QUERY rdma_resolve_ip(addr_handler) #1 process_one_req(): for #1 addr_handler(): RDMA_CM_ADDR_QUERY -> RDMA_CM_ADDR_BOUND mutex_unlock(&id_priv->handler_mutex); [.. handler still running ..] rdma_resolve_addr(): RDMA_CM_ADDR_BOUND -> RDMA_CM_ADDR_QUERY rdma_resolve_ip(addr_handler) !! two requests are now on the req_list rdma_destroy_id(): destroy_id_handler_unlock(): _destroy_id(): cma_cancel_operation(): rdma_addr_cancel() // process_one_req() self removes it spin_lock_bh(&lock); cancel_delayed_work(&req->work); if (!list_empty(&req->list)) == true ! rdma_addr_cancel() returns after process_on_req #1 is done kfree(id_priv) process_one_req(): for #2 addr_handler(): mutex_lock(&id_priv->handler_mutex); !! Use after free on id_priv rdma_addr_cancel() expects there to be one req on the list and only cancels the first one. The self-removal behavior of the work only happens after the handler has returned. This yields a situations where the req_list can have two reqs for the same "handle" but rdma_addr_cancel() only cancels the first one. The second req remains active beyond rdma_destroy_id() and will use-after-free id_priv once it inevitably triggers. Fix this by remembering if the id_priv has called rdma_resolve_ip() and always cancel before calling it again. This ensures the req_list never gets more than one item in it and doesn't cost anything in the normal flow that never uses this strange error path. | |||||
| CVE-2021-47383 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 7.1 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: tty: Fix out-of-bound vmalloc access in imageblit This issue happens when a userspace program does an ioctl FBIOPUT_VSCREENINFO passing the fb_var_screeninfo struct containing only the fields xres, yres, and bits_per_pixel with values. If this struct is the same as the previous ioctl, the vc_resize() detects it and doesn't call the resize_screen(), leaving the fb_var_screeninfo incomplete. And this leads to the updatescrollmode() calculates a wrong value to fbcon_display->vrows, which makes the real_y() return a wrong value of y, and that value, eventually, causes the imageblit to access an out-of-bound address value. To solve this issue I made the resize_screen() be called even if the screen does not need any resizing, so it will "fix and fill" the fb_var_screeninfo independently. | |||||
| CVE-2023-52803 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: SUNRPC: Fix RPC client cleaned up the freed pipefs dentries RPC client pipefs dentries cleanup is in separated rpc_remove_pipedir() workqueue,which takes care about pipefs superblock locking. In some special scenarios, when kernel frees the pipefs sb of the current client and immediately alloctes a new pipefs sb, rpc_remove_pipedir function would misjudge the existence of pipefs sb which is not the one it used to hold. As a result, the rpc_remove_pipedir would clean the released freed pipefs dentries. To fix this issue, rpc_remove_pipedir should check whether the current pipefs sb is consistent with the original pipefs sb. This error can be catched by KASAN: ========================================================= [ 250.497700] BUG: KASAN: slab-use-after-free in dget_parent+0x195/0x200 [ 250.498315] Read of size 4 at addr ffff88800a2ab804 by task kworker/0:18/106503 [ 250.500549] Workqueue: events rpc_free_client_work [ 250.501001] Call Trace: [ 250.502880] kasan_report+0xb6/0xf0 [ 250.503209] ? dget_parent+0x195/0x200 [ 250.503561] dget_parent+0x195/0x200 [ 250.503897] ? __pfx_rpc_clntdir_depopulate+0x10/0x10 [ 250.504384] rpc_rmdir_depopulate+0x1b/0x90 [ 250.504781] rpc_remove_client_dir+0xf5/0x150 [ 250.505195] rpc_free_client_work+0xe4/0x230 [ 250.505598] process_one_work+0x8ee/0x13b0 ... [ 22.039056] Allocated by task 244: [ 22.039390] kasan_save_stack+0x22/0x50 [ 22.039758] kasan_set_track+0x25/0x30 [ 22.040109] __kasan_slab_alloc+0x59/0x70 [ 22.040487] kmem_cache_alloc_lru+0xf0/0x240 [ 22.040889] __d_alloc+0x31/0x8e0 [ 22.041207] d_alloc+0x44/0x1f0 [ 22.041514] __rpc_lookup_create_exclusive+0x11c/0x140 [ 22.041987] rpc_mkdir_populate.constprop.0+0x5f/0x110 [ 22.042459] rpc_create_client_dir+0x34/0x150 [ 22.042874] rpc_setup_pipedir_sb+0x102/0x1c0 [ 22.043284] rpc_client_register+0x136/0x4e0 [ 22.043689] rpc_new_client+0x911/0x1020 [ 22.044057] rpc_create_xprt+0xcb/0x370 [ 22.044417] rpc_create+0x36b/0x6c0 ... [ 22.049524] Freed by task 0: [ 22.049803] kasan_save_stack+0x22/0x50 [ 22.050165] kasan_set_track+0x25/0x30 [ 22.050520] kasan_save_free_info+0x2b/0x50 [ 22.050921] __kasan_slab_free+0x10e/0x1a0 [ 22.051306] kmem_cache_free+0xa5/0x390 [ 22.051667] rcu_core+0x62c/0x1930 [ 22.051995] __do_softirq+0x165/0x52a [ 22.052347] [ 22.052503] Last potentially related work creation: [ 22.052952] kasan_save_stack+0x22/0x50 [ 22.053313] __kasan_record_aux_stack+0x8e/0xa0 [ 22.053739] __call_rcu_common.constprop.0+0x6b/0x8b0 [ 22.054209] dentry_free+0xb2/0x140 [ 22.054540] __dentry_kill+0x3be/0x540 [ 22.054900] shrink_dentry_list+0x199/0x510 [ 22.055293] shrink_dcache_parent+0x190/0x240 [ 22.055703] do_one_tree+0x11/0x40 [ 22.056028] shrink_dcache_for_umount+0x61/0x140 [ 22.056461] generic_shutdown_super+0x70/0x590 [ 22.056879] kill_anon_super+0x3a/0x60 [ 22.057234] rpc_kill_sb+0x121/0x200 | |||||
| CVE-2023-52796 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 7.8 HIGH |
| In the Linux kernel, the following vulnerability has been resolved: ipvlan: add ipvlan_route_v6_outbound() helper Inspired by syzbot reports using a stack of multiple ipvlan devices. Reduce stack size needed in ipvlan_process_v6_outbound() by moving the flowi6 struct used for the route lookup in an non inlined helper. ipvlan_route_v6_outbound() needs 120 bytes on the stack, immediately reclaimed. Also make sure ipvlan_process_v4_outbound() is not inlined. We might also have to lower MAX_NEST_DEV, because only syzbot uses setups with more than four stacked devices. BUG: TASK stack guard page was hit at ffffc9000e803ff8 (stack is ffffc9000e804000..ffffc9000e808000) stack guard page: 0000 [#1] SMP KASAN CPU: 0 PID: 13442 Comm: syz-executor.4 Not tainted 6.1.52-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/09/2023 RIP: 0010:kasan_check_range+0x4/0x2a0 mm/kasan/generic.c:188 Code: 48 01 c6 48 89 c7 e8 db 4e c1 03 31 c0 5d c3 cc 0f 0b eb 02 0f 0b b8 ea ff ff ff 5d c3 cc 00 00 cc cc 00 00 cc cc 55 48 89 e5 <41> 57 41 56 41 55 41 54 53 b0 01 48 85 f6 0f 84 a4 01 00 00 48 89 RSP: 0018:ffffc9000e804000 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff817e5bf2 RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffffffff887c6568 RBP: ffffc9000e804000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: dffffc0000000001 R12: 1ffff92001d0080c R13: dffffc0000000000 R14: ffffffff87e6b100 R15: 0000000000000000 FS: 00007fd0c55826c0(0000) GS:ffff8881f6800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffc9000e803ff8 CR3: 0000000170ef7000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <#DF> </#DF> <TASK> [<ffffffff81f281d1>] __kasan_check_read+0x11/0x20 mm/kasan/shadow.c:31 [<ffffffff817e5bf2>] instrument_atomic_read include/linux/instrumented.h:72 [inline] [<ffffffff817e5bf2>] _test_bit include/asm-generic/bitops/instrumented-non-atomic.h:141 [inline] [<ffffffff817e5bf2>] cpumask_test_cpu include/linux/cpumask.h:506 [inline] [<ffffffff817e5bf2>] cpu_online include/linux/cpumask.h:1092 [inline] [<ffffffff817e5bf2>] trace_lock_acquire include/trace/events/lock.h:24 [inline] [<ffffffff817e5bf2>] lock_acquire+0xe2/0x590 kernel/locking/lockdep.c:5632 [<ffffffff8563221e>] rcu_lock_acquire+0x2e/0x40 include/linux/rcupdate.h:306 [<ffffffff8561464d>] rcu_read_lock include/linux/rcupdate.h:747 [inline] [<ffffffff8561464d>] ip6_pol_route+0x15d/0x1440 net/ipv6/route.c:2221 [<ffffffff85618120>] ip6_pol_route_output+0x50/0x80 net/ipv6/route.c:2606 [<ffffffff856f65b5>] pol_lookup_func include/net/ip6_fib.h:584 [inline] [<ffffffff856f65b5>] fib6_rule_lookup+0x265/0x620 net/ipv6/fib6_rules.c:116 [<ffffffff85618009>] ip6_route_output_flags_noref+0x2d9/0x3a0 net/ipv6/route.c:2638 [<ffffffff8561821a>] ip6_route_output_flags+0xca/0x340 net/ipv6/route.c:2651 [<ffffffff838bd5a3>] ip6_route_output include/net/ip6_route.h:100 [inline] [<ffffffff838bd5a3>] ipvlan_process_v6_outbound drivers/net/ipvlan/ipvlan_core.c:473 [inline] [<ffffffff838bd5a3>] ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:529 [inline] [<ffffffff838bd5a3>] ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline] [<ffffffff838bd5a3>] ipvlan_queue_xmit+0xc33/0x1be0 drivers/net/ipvlan/ipvlan_core.c:677 [<ffffffff838c2909>] ipvlan_start_xmit+0x49/0x100 drivers/net/ipvlan/ipvlan_main.c:229 [<ffffffff84d03900>] netdev_start_xmit include/linux/netdevice.h:4966 [inline] [<ffffffff84d03900>] xmit_one net/core/dev.c:3644 [inline] [<ffffffff84d03900>] dev_hard_start_xmit+0x320/0x980 net/core/dev.c:3660 [<ffffffff84d080e2>] __dev_queue_xmit+0x16b2/0x3370 net/core/dev.c:4324 [<ffffffff855ce4cd>] dev_queue_xmit include/linux/netdevice.h:3067 [inline] [<ffffffff855ce4cd>] neigh_hh_output include/net/neighbour.h:529 [inline] [<f ---truncated--- | |||||
| CVE-2023-52792 | 1 Linux | 1 Linux Kernel | 2025-09-23 | N/A | 5.5 MEDIUM |
| In the Linux kernel, the following vulnerability has been resolved: cxl/region: Do not try to cleanup after cxl_region_setup_targets() fails Commit 5e42bcbc3fef ("cxl/region: decrement ->nr_targets on error in cxl_region_attach()") tried to avoid 'eiw' initialization errors when ->nr_targets exceeded 16, by just decrementing ->nr_targets when cxl_region_setup_targets() failed. Commit 86987c766276 ("cxl/region: Cleanup target list on attach error") extended that cleanup to also clear cxled->pos and p->targets[pos]. The initialization error was incidentally fixed separately by: Commit 8d4285425714 ("cxl/region: Fix port setup uninitialized variable warnings") which was merged a few days after 5e42bcbc3fef. But now the original cleanup when cxl_region_setup_targets() fails prevents endpoint and switch decoder resources from being reused: 1) the cleanup does not set the decoder's region to NULL, which results in future dpa_size_store() calls returning -EBUSY 2) the decoder is not properly freed, which results in future commit errors associated with the upstream switch Now that the initialization errors were fixed separately, the proper cleanup for this case is to just return immediately. Then the resources associated with this target get cleanup up as normal when the failed region is deleted. The ->nr_targets decrement in the error case also helped prevent a p->targets[] array overflow, so add a new check to prevent against that overflow. Tested by trying to create an invalid region for a 2 switch * 2 endpoint topology, and then following up with creating a valid region. | |||||